S3C2416 Linux-2.6.35 kernel porting file system cannot hang up, you help me this

CPU: S3C2416@534MHz
Fclk = 534MHz, Hclk = 133MHz, Pclk = 66MHz
DRAM: 128 MB
NAND: 512 MB
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0

NAND read: device 0 offset 0x900000, size 0x300000
3145728 bytes read: OK
Boot with zImage

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Linux version 2.6.35 (root@ljf-desktop) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-176) ) #4 Sat Aug 3 17:04:19 CST 2013
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: SMDK2416
Memory policy: ECC disabled, Data cache writeback
CPU S3C2416/S3C2450 (id 0x32450003)
S3C24XX Clocks, Copyright 2004 Simtec Electronics
CPU: MPLL on 534.000 MHz, cpu 534.000 MHz, mem 133.500 MHz, pclk 66.750 MHz
CPU: EPLL on 96.000 MHz, usb-bus 48.000 MHz
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Kernel command line: mem=128M console=ttySAC0,115200n8 noinitrd root=/dev/mtdblock3 rw init=/linuxrc rootfstype=jffs2
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 125716k/125716k available, 5356k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
vmalloc : 0xc8800000 - 0xe0000000 ( 376 MB)
lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc0029000 ( 132 kB)
.text : 0xc0029000 - 0xc03b4000 (3628 kB)
.data : 0xc03cc000 - 0xc03ef380 ( 141 kB)
Hierarchical RCU implementation.
RCU-based detection of stalled CPUs is disabled.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:99
irq: clearing subpending status 00000002
Console: colour dummy device 80x30
console [ttySAC0] enabled
Calibrating delay loop... 266.24 BogoMIPS (lpj=665600)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
gpiochip_add: gpios 256..271 (GPIOJ) failed to register
gpiochip_add: gpios 288..303 (GPIOK) failed to register
gpiochip_add: gpios 320..334 (GPIOL) failed to register
gpiochip_add: gpios 352..353 (GPIOM) failed to register
NET: Registered protocol family 16
S3C Power Management, Copyright 2004 Simtec Electronics
S3C2416: Initializing architecture
S3C2416: IRQ Support
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
s3c-i2c s3c2410-i2c: slave address 0x10
s3c-i2c s3c2410-i2c: bus frequency set to 65 KHz
s3c-i2c s3c2410-i2c: i2c-0: S3C I2C adapter
Advanced Linux Sound Architecture Driver Version 1.0.23.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
NetWinder Floating Point Emulator V0.97 (extended precision)
JFFS2 version 2.2. (NAND) (SUMMARY) Drain 2001-2006 Red Hat, Inc.
ROMFS MTD (C) 2007 Red Hat, Inc.
msgmni has been set to 245
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
s3c2440-uart.0: s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440
s3c2440-uart.1: s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440
s3c2440-uart.2: s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440
brd: module loaded
loop: module loaded
Uniform Multi-Platform E-IDE driver
ide-gd driver 1.18
ide-cd driver 5.00
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c24xx-nand s3c2440-nand: Tacls=2, 14ns Twrph0=4 29ns, Twrph1=2 14ns
s3c24xx-nand s3c2440-nand: NAND ECC disabled
NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bit)
NAND_ECC_NONE selected by board driver. This is not recommended !!
Scanning device for bad blocks
Bad eraseblock 0 at 0x000000000000
Bad eraseblock 5 at 0x000001400000
Bad eraseblock 6 at 0x000001800000
Bad eraseblock 7 at 0x000001c00000
Creating 4 MTD partitions on "NAND 512MiB 3,3V 8-bit":
0x000000000000-0x000000100000 : "2416_Boot"
0x000000100000-0x000000900000 : "2416_space"
0x000000900000-0x000000c00000 : "2416_kernel"
0x000000c00000-0x000020000000 : "2416_rootfs"
dm9000 Ethernet Driver, V1.31
usbmon: debugfs is not available
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usbcore: registered new interface driver libusual
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver ftdi_sio
ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
mice: PS/2 mouse device common for all mice
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
No device for DAI UDA134X
No device for DAI s3c24xx-i2s
ALSA device list:
No soundcards found.
TCP cubic registered
NET: Registered protocol family 17
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
usb 1-1: new full speed USB device using s3c2410-ohci and address 2
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
VFS: Mounted root (jffs2 filesystem) on device 31:3.
Freeing init memory: 132K
Failed to execute /linuxrc. Attempting defaults...
Kernel panic - not syncing: No init found. Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.
[<c002f314>] (unwind_backtrace+0x0/0xec) from [<c02d6784>] (panic+0x54/0xdc)
[<c02d6784>] (panic+0x54/0xdc) from [<c0029564>] (init_post+0x9c/0xbc)
[<c0029564>] (init_post+0x9c/0xbc) from [<c00085f4>] (kernel_init+0x110/0x14c)
[<c00085f4>] (kernel_init+0x110/0x14c) from [<c002ae18>] (kernel_thread_exit+0x0/0x8)

Here, on this side of the file system is used, with other kernel can be mounted.
The compiler uses the kernel and file system is the same.

I also search the Internet for a long time, many methods are tried, still can't get it out.

Started by Tammy at November 14, 2016 - 3:24 AM

Failed to execute /Linuxrc implementation of this file failed,
Your bootloader boot parameters configuration error. Is it right?.

Posted by Z at November 25, 2016 - 4:02 AM

mem=128M console=ttySAC0,115200n8 noinitrd root=/dev/mtdblock3 rw init=/linuxrc rootfstype=jffs2

This should be true.?

Posted by Tammy at November 26, 2016 - 4:43 AM

The presence of linuxrc this file you?

Posted by Z at December 09, 2016 - 4:59 AM

The presence of linuxrc this document, is executable.
It is like this:
I before the kernel is 2.6.21, now is a kernel upgrade to 2.6.35. The file system is invariant. If there is no problem with the 21 kernel. So here I'm sure the file system is not a problem, it is the kernel problem. And then have to struggle with this issue. .

Posted by Tammy at December 11, 2016 - 5:05 AM

mem=64M console=ttySAC0,115200 no_console_suspend root=/dev/mtdblock3 rootfstype=jffs2 mtdparts=384K(u-boot),128K(u-boot-env),5M(kernel),120M(root)
I was linux-2.3.36 S3C2440 reference.

Posted by Abbott at December 14, 2016 - 5:10 AM

This problem is generally parameter configuration error

Posted by Jacob at December 15, 2016 - 5:43 AM



This is the detailed steps I transplant, I have tracked down the code, or do not know how to solve.

Don't know what parameter configuration will be more likely to cause this problem, can explain the next?

Posted by Tammy at December 23, 2016 - 6:09 AM

You are to mount. Kernel tailoring, may not add card driver; or TFTP server is not configured

Posted by Lauren at December 30, 2016 - 6:16 AM

The two will also affect the file system mount, dizzy. I try under the kazakhstan. Thank you

Posted by Tammy at January 03, 2017 - 7:32 AM

1, There may now give you a grid file system?
2, The kernel image loading before you try, you can run, if not, to burn the file system.,
3, 2 if not on, so when you compile a new kernel in the filesystem options enable support for JFFS2. See your log information, use the JFFS2 file system to

Posted by Isidore at January 08, 2017 - 6:46 AM

The kernel and file system whether the compiler.

Posted by Everley at January 10, 2017 - 6:52 AM